Box Assembly
Yesterday night I returned to the shop. The bottom and insides of the cherry dovetailed box had been finished with two coats of Tung oil finish and a coat of wax. The finished cherry glowed almost golden, practically begging me to glue it together.
Having come this far without incident, I wanted to be sure to get the glue up right. I checked my labels, still visible on the outside of the box, and laid out the parts in relative position with the bottom in the center. I placed the sides with the bottom slots of each piece laid alongside the bottom. I had clamps ready if I should need them; also a 12" rule, a mallet, four pine blocks cut with fingers slightly thinner than the tails, glue spreaders and glue cup cut from a small paper cup, a spray bottle of water, paper towels, and scraps of cherry created when I cut the dovetails.
Surveying the scene, I ran through the process in my head. It seemed that everything I needed lay in front of me. I used some poster putty to temporarily attach the paper glue cup to the bench top (have you ever chased a glue cup under the bench while your open time was ticking away? I have.). Then I poured enough wood glue into the cup and started spreading glue on the long grain of the pin boards. Perhaps I should have also spread glue on the tail boards, but I chose not to do so. I knew the tails had a fairly tight fit, and I wanted to minimize squeeze out.
After adding glue to all the pins, I lightly inserted one set of tails into the corresponding sets of pins, first on one side and then the other. Using one of the pine blocks to protect the cherry side from the mallet, I tapped the end home, working alternately from one edge to the other. When that end was set, I turned the box over and slid the bottom into its slot, then repeated the process of inserting the tails and driving the second end home.
I now had a box. Using the 12' rule, I tested for square. Then I looked at the inside for squeeze out. At this point I realized two sections were not driven all the way home, so I applied the mallet just a little bit harder to drive them into place. The box was still square, and there was only one spot of squeeze out. Since the inside was already finished, cleaning this was no big deal. I sprayed a paper towel lightly with water and wiped away the glue spot.
At the last, I looked at the dovetails critically. Only one spot looked like it needed significant help, so I made a small wedge from one of the cherry scraps. I dipped this in glue and lightly tapped it into the gap (making sure to line up the grain so it would appear to be part of the pin – I think end grain hides better than edge grain and its easier to make the wedge that way). So now the assembly is done. My only worry is that I may have driven this wedge a little too far and deformed the tail enough to be noticeable. We'll see tonight when I trim it flush.
Having come this far without incident, I wanted to be sure to get the glue up right. I checked my labels, still visible on the outside of the box, and laid out the parts in relative position with the bottom in the center. I placed the sides with the bottom slots of each piece laid alongside the bottom. I had clamps ready if I should need them; also a 12" rule, a mallet, four pine blocks cut with fingers slightly thinner than the tails, glue spreaders and glue cup cut from a small paper cup, a spray bottle of water, paper towels, and scraps of cherry created when I cut the dovetails.
Surveying the scene, I ran through the process in my head. It seemed that everything I needed lay in front of me. I used some poster putty to temporarily attach the paper glue cup to the bench top (have you ever chased a glue cup under the bench while your open time was ticking away? I have.). Then I poured enough wood glue into the cup and started spreading glue on the long grain of the pin boards. Perhaps I should have also spread glue on the tail boards, but I chose not to do so. I knew the tails had a fairly tight fit, and I wanted to minimize squeeze out.
After adding glue to all the pins, I lightly inserted one set of tails into the corresponding sets of pins, first on one side and then the other. Using one of the pine blocks to protect the cherry side from the mallet, I tapped the end home, working alternately from one edge to the other. When that end was set, I turned the box over and slid the bottom into its slot, then repeated the process of inserting the tails and driving the second end home.
I now had a box. Using the 12' rule, I tested for square. Then I looked at the inside for squeeze out. At this point I realized two sections were not driven all the way home, so I applied the mallet just a little bit harder to drive them into place. The box was still square, and there was only one spot of squeeze out. Since the inside was already finished, cleaning this was no big deal. I sprayed a paper towel lightly with water and wiped away the glue spot.
At the last, I looked at the dovetails critically. Only one spot looked like it needed significant help, so I made a small wedge from one of the cherry scraps. I dipped this in glue and lightly tapped it into the gap (making sure to line up the grain so it would appear to be part of the pin – I think end grain hides better than edge grain and its easier to make the wedge that way). So now the assembly is done. My only worry is that I may have driven this wedge a little too far and deformed the tail enough to be noticeable. We'll see tonight when I trim it flush.
Labels: Basic Concepts, Dovetails, Process
posted by rookster at
3:04 PM
0 Comments:
Post a Comment
Links to this post:
Create a Link
<< Home